How to resolve error code F2 with sharp AR-5620

Sharp AR-5618, AR-5620 error code F2

How to resolve error code F2 with sharp AR-5620

Here in this article I explain how to solve your Sharp AR-5620, AR-5618 error code F2. This should solve your problem. We are sharing a few methods to fix the F2 error in Sharp AR-5618, AR-5620,AR-5623, AR-5520 and AR-5516 so check them one by one until it gets solved.

How fix the F2 error code.

F2 code means problem with toner cartridge error. Sometimes F2 is caused by lose or broken harness in scanning section, in this case it sometimes display an E7 code. When f2 flashes on display just press start key you will receive a sub code. If sub code is F2-02 this is toner supply problem. If F2-04 toner chip is damaged, replace the chip. If F2-40 developer is damaged, change the developer.

·        Clean toner cartridge CRUM chip contacts and check if cartridge destination is proper for your area.

·        This code you may have to clean out the developing unit and start with fresh developer. Make sure the developer unit is not leaking from one of the bearings. You may need a tech for this one.

·        Replace the toner cartridge.

·        Change the developer.

If you find your parts, then replace the parts and error still remains, after automatically reset the error code. If the error is still showing even after above solutions, then you have no choice other than calling Sharp service technician.

I hope this was helpful, don’t forget to share it via any of the share buttons on this page are highly welcomed as well.

How do you reset a C6000 error on a Kyocera KM-2530/km-3530/km-4035

Kyocera KM-2530, KM-4030, KM-3530 error code C6000

Here in this article I explain how to solve your Kyocera Mita km 2530 error code c6000. This article will help you to troubleshoot some common error messages related to Error Code C602O, C6050 that you may receive any of the Kyocera Mita-2530, KM-2540, KM-2550, KM-2560, KM-3035, KM-3040, KM-3050, KM-3060, KM-3530, KM-4030, KM-4035 and KM-4050 models.

Meaning of the C6000 Error Code

Kyocera error code C6000 is displayed when your machine fails to reach the correct temperature at a specific time. Fixing unit thermistor 1 detected less than 70C for 10 second during warm-up and ready in. the temperature at the fuser unit thermistor 1 does not rise by 1C/1.8F continuously for 5 s. Fuser unit thermistor 2 detected less than 40C for 10 s during warm-up and ready in. the temperature at the fuser unit thermistor 2 does not rise by 1C/1.8F continuously for 5 s. In some cases, you can solve the error code C6000 by resetting it or when it is a false error, can’t be reset it and may also require new parts.

How to reset the fixing error

To reset this error, do the following.

1.   Press the number key in 10871087 the display should blink.

2.   The display change to Maintenance mode.

3.   Press the 163 and press the start key, the screen for executing is displayed.

4.   Select the EXECUTE and press ENTER

5.   Turn the copier OFF, wait 20 seconds and power up the machine. The fixing problem data is initialized.

It is an error on your heater unit. It sometimes comes with power fluctuation. If you do not know about copiers and their settings then i advice you to rather get a Kyocera technician to do it for you.

I hope this was helpful, don’t forget to share it via any of the share buttons on this page are highly welcomed as well.

How to refill toner cartridge Sharp ar 6020/ar 6023/ar 6026/ar 6031

Toner cartridge refilling in sharp ar 6020, ar 6023, ar 6026 and ar 6031

Here in this post I explain how to refill toner cartridge in sharp AR 6020, AR 6023, AR6026 and AR 6031 series copier.

I don’t recommend refilling a sharp ar 6020 series toner cartridge because the toner powder is very fine and you do not want to breathe in this toner powder. I would advise purchasing a new toner cartridge for your model of sharp copier. Authentic sharp dealers will give you original toner cartridge, non-sharp toner providers may be sells the poor quality toner refill Kits.

If you want to do toner cartridge refilling, the toner cartridge comes with on-chip sensor in back side of toner cartridge that counts the toner life. If you allow it to go empty completely that is it gives red triangle which is steady to warn that toner is near empty. You should replenish toner at this time but if you allow it to blink red triangle that means it’s completely over and can't be refilled. Take the toner out of the printer and refilling a new toner powder it carefully. Below is the video guide to refill the sharp ar 6020. However, it is advisable only if the existing cartridge is in a good condition. It is always better to replace supplies with original as they provide good yield.

I hope this was helpful, don’t forget to share it via any of the share buttons on this page are highly welcomed as well.

KONICA MINOLTA C350 AUTO COLOUR ADJUSTMENT PROBLEM

KONICA MINOLTA C350/C450 Auto Colour Calibration

These instructions describe how to adjust Auto Colour Calibration for a Konica Minolta C250, C350 and C450 copier machine. Colours are too dark or severely tinting to one range of colour such as yellow, cyan or more commonly magenta on printed documents. This issue is most noticeable on grey halftones.

 Please note that these issues must occur on ALL printouts. If only one computer or a single piece of software is having poor colour reproduction, please troubleshoot the computer or software. Please also note that grey halftones will NEVER be perfect and usually will tint slightly to magenta or brown.

STEPS:

1.  Press the Utility button to the left side of the LCD screen.

2.  Tech the Admin Mode.

3.  The machine will ask for a password, press the password 00000000

4.  Next select Gradation Adjustment.

5.  You can see the START button Green light up, then Press the Start button to print out the adjustment test pattern. The print out may take 30-60 Seconds to print out. If the start button is Orange, you must load either Letter paper in Portrait direction or Ledger paper into one of the trays.

6.  When the test pattern is printed, examine the pattern. Notice that on edge of the pattern there are Two Black Squares. Place the test pattern Face-Down on the scanner glass with the Black Squares against the Left-hand Side Ruler.

7.  Close the scanner lid and press the Start Button. The scanner will scan 3 times.

 8.  Press the Exit twice to bring the screen back to copy mode.

 9.  The Auto Colour Calibration is complete. You should see improvement in your colour reproduction when printing. If the issue continues, please call your servicing company for more instruction or repair.

I hope this was helpful, don’t forget to share it via any of the share buttons on this page are highly welcomed as well.

Kyocera TaskAlfa Default Username and Password

Here in this post I explain Kyocera TaskAlfa series administration username and password

Kyocera TaskAlfa Default Username and Password

Model number	Username	Password
TaskAlfa 180, 181, 220, 221	Admin	Admin
TaskAlfa 1800, 1801,2200, 2201	Admin	Admin
TaskAlfa 2420w, 4820w
TaskAlfa 250i, 300ci, 400ci, 500ci, 552ci		Admin
TaskAlfa 2550ci, 3050ci	Admin	Admin
TaskAlfa 2551ci	Admin	Admin
TaskAlfa 2552ci, 3252ci, 4052ci, 5052, 6052ci	Admin	Admin
TaskAlfa 265CI, 266CI	Admin	Admin
TaskAlfa 300i	Admin	Admin
TaskAlfa 350ci	Admin	Admin
TaskAlfa TA6551ci	Admin	Admin
TaskAlfa 3050ci, 3550ci	Admin	Admin
TaskAlfa 3501i, 4501i, 5501i	Admin	Admin
TaskAlfa 3010i, 3510i	Admin	Admin
TaskAlfa 3011i,3511i	Admin	Admin
TaskAlfa 306ci	Admin	Admin
TaskAlfa 3212i, 4012i	Admin	Admin
TaskAlfa 3500i, 4500i, 5500i	Admin	Admin
TaskAlfa 3510ci	Admin	Admin
TaskAlfa 351ci	Admin	Admin
TaskAlfa 3051ci, 3551ci, 4551ci, 5551ci	Admin	Admin
TaskAlfa 356ci, 406ci	Admin	Admin
TaskAlfa 4002i, 5002i, 6002i	Admin	Admin
TaskAlfa 420i, 520i	Admin	Admin
TaskAlfa 4550ci, 5550ci	Admin	Admin
TaskAlfa 550c, 650c, 750c	Admin	Admin
TaskAlfa 620, 820	Admin	Admin
TaskAlfa 6501i, 8001i	Admin	Admin
TaskAlfa 6550ci, 7550ci	Admin	Admin
TaskAlfa 6551ci, 7551ci	Admin	Admin
TaskAlfa 7002i, 8002i, 9002i	Admin	Admin
TaskAlfa 7052ci, 8052ci	Admin	Admin
TaskAlfa 6500i, 8000i	Admin	Admin

Olivetti d-copia 200mf reset the error code c6000

error code c6000 solved on olivetti d-copia 200mf and d-copia 250mf

Olivetti d-copia 200mf reset the error code c6000

Here in this post I explain how to fix error code C6000 in OLIVETTI D-copia 200MF, D-copia 250MF, which should solve your problem. We are sharing a few methods to clear the error C6000 code in Olivetti D-Copia series, so check them one by one until it gets solved.

Maintenance sign means that the copier needs to be well serviced or something has to be replaced like Consumables such as drum, blade, fuser rollers and developer etc. If you are sure that you replaced the correct parts or the machine doesn't need to replace any part, then you can continue to clear the sign.

 

Meaning of the C6000 error code

Olivetti D-copier 200mf error code C6000 is displayed when your machine fails to reach the correct temperature at a specific time. The temperature does not become 100°C/212°F even if 30 s pass before secondary stabilization. When there is no 1°C/1.8°F rise in 5 s before secondary stabilization. Basically you have to check if the fuser is warming up (the halogen lamps inside are lighten up). If not heating, you will have to replace it.

How to fix the error:

You have to reset the fuser code manually.

1.     Open top cover then turn ON the machine, then presses the System Menu then scroll down to Service Setting, then HOLD BOTH the "Start key" and "#" and press "OK".

2.     Scroll down to Maintenance Mode then press "OK".

3.     Then press 163 on the keypad

4.     Scroll down to "Execute"

5.     Then press "OK"

6.     And turn off power then back on.

If the error C6000 appears again then get your unit checked for fuser unit and fuser unit heat issues.

Fuser removal: Remove rear cover, top cover, left and right cover. Remove two screws. Unplug two connectors. Pull out Fuser unit. Remove two screws, separate the upper part from the lower part, and remove separation claws (3pcs each 1 held w/ screws at the rear). Remove and check heater lamp, upper fuser roller and thermostat (circular shape). After replace the parts then reset manually.

I hope this was helpful, don’t forget to share it via any of the share buttons on this page are highly welcomed as well.

How to solve my Kyocera Taskalfa 1800 ask to "add toner" problem

Kyocera TaskAlfa 1800 add toner error solution

How to solve my Kyocera Taskalfa 1800 ask to "add toner" problem

How to solve my Kyocera Taskalfa 1800 ask to add toner even though the toner was full and did not work. The following instructions describe how to reset add toner error for a Kyocera TaskAlfa 1800, 1801, 2200 and 2201 copier machine. We are sharing a few methods to solution the problem, so check them one by one until it gets solved.

Meaning of the add toner Error:

Kyocera Taskalfa is showing add toner on its screen even after another toner has been fixed. Kyocera products are very particular when it comes to the toner used if you are using toner that is not model specific Kyocera Taskalfa toner you can have this problem you can try Kyocera Taskalfa toner now but you may have destroyed the developer in which case you need fresh dev and model specific Kyocera Taskalfa toner don't use toner that says for use in look for the Kyocera Taskalfa logo on the box.

How to fix the add toner problem:

Resolve this problem you have to choice if the first one didn't work gone to the next one. Do the following procedure to reset the error:-

1.     You either got a bad toner (the chip on it is telling it is bad). Open the front cover and replace it with the new toner then close the front cover. Make sure new toner is shaking well.

2.     You must use OEM toner if you haven't been then you have to empty developer unit and start with OEM toner.

3.     Replace the toner chip.

4.     developer unit probably went bad

  I hope this was helpful, don’t forget to share it via any of the share buttons on this page are highly welcomed as well.